| Paper bag with handles |
- Bottom flap must be at least 2 mm less than the gusset depth.
- Bottom flap must be at least half the gusset plus 10 mm, so the flaps overlap.
|
| Pinch bottom paper bag |
- The seam must sit on the back: at least 10 mm less than the width.
|
| Baguette bag |
- The seam must sit on the back: at least 10 mm less than the width.
|
| French fry bag |
- The seam must sit on the back: at least 10 mm less than the width.
|
| Flat bottom pouch |
- Gusset can't be deeper than the width
- Zipper too low for this height
|
| Cup sleeve |
- Bottom Ø must be smaller than the top Ø.
- The sleeve runs past the bottom of the cup. Lower the sleeve height or its distance from the rim.
- Too much taper for a sleeve. Check the diameters and the height.
|
| Hang tag |
- The hole is too close to the top edge.
- The hole is wider than the tag.
- The hole is too low for this tag.
|
| Envelope |
- A wallet envelope opens on its long side: make the height no more than the width.
|
| Tuck flap envelope |
- A wallet envelope opens on its long side: make the height no more than the width.
|
| Pocket folder |
- The pocket can be at most half the folder's height.
- Card slits need a pocket at least 60 mm tall.
|
| Self-locking folder |
- Too tall for its width: the lock no longer fits. Keep the height within 4 times the width.
|
| Mailer box |
- Thickness must be under a fifth of the height.
|
| Tuck box |
- Up to 2 mm board for this box.
|
| Tuck box with hang tab |
- Up to 2 mm board for this box.
- Tab height can be at most half the box height
- Length must be at least 45 mm for the hang hole
|
| Crash lock bottom box |
- Up to 2 mm board for this box.
- Too wide for the crash lock: keep width ≤ 1.5 × length − 12 mm.
- Thickness must be under a fifth of the height.
|
| Gable box |
- Up to 2 mm board for this box.
- Too wide for the self-locking bottom: keep width ≤ 1.5 × length − 12 mm.
|
| Cake box with handle |
- Up to 2 mm board for this box.
- Too wide for the self-locking bottom: keep width ≤ 1.5 × length − 12 mm.
- Thickness must be under a fifth of the height.
|
| Snap lock bottom box |
- Thickness must be under a fifth of the height.
- Length must be at least 45 mm for the hang hole
- Height must be at least 50 mm for the hang tab
- Height must be at least 60 mm for the tear strip
|
| Snap lock box with handle |
- Thickness must be under a fifth of the height.
- Length must be at least 45 mm for the hang hole
- Height must be at least 50 mm for the hang tab
- Height must be at least 60 mm for the tear strip
|
| Roof box |
- Thickness must be under a fifth of the height.
- Length must be at least 45 mm for the hang hole
- Height must be at least 50 mm for the hang tab
- Height must be at least 60 mm for the tear strip
|
| Flip top box |
- Thickness must be under a fifth of the height.
- Length must be at least 45 mm for the hang hole
- Height must be at least 50 mm for the hang tab
- Height must be at least 60 mm for the tear strip
|
| Angled top box |
- Thickness must be under a fifth of the height.
- Length must be at least 45 mm for the hang hole
- Height must be at least 50 mm for the hang tab
- Height must be at least 60 mm for the tear strip
|
| Pillow box |
- Width must not exceed length.
- Height must be at least 0.15 × width.
- Height must be at most 0.41 × width.
|
| Shipping box |
- Width must not exceed length.
|
| Tuck lid shipping box |
- Width must not exceed length.
|
| Tissue box |
- Up to 0.8 mm board for this box.
- Width must not exceed length.
|
| Carry handle box |
- Up to 0.8 mm board for this box.
- Width must not exceed length.
|
| Tab lock mailer box |
- Up to 3 mm board for this box.
- Thickness must be under a fifth of the height.
- Width must not exceed length.
- Height must not exceed width.
|
| Shoe box |
- Up to 3 mm board for this box.
- Width must not exceed length.
- Too short for this height: the lid's corner locks would meet. Keep the length at least 150 mm + two thirds of the height.
|
| Pizza slice box |
- Up to 1.6 mm board for this box.
- Too wide for this length: the tip would open past a right angle. Keep the width within twice the length.
- Too narrow for this length: the tip would be too sharp to fold. Keep the width at least half the length.
- At least 30 mm high: lower walls leave no room for the locks.
- Too high for this slice: the lock tabs would cover each other's slots. Lower the height or make the slice longer.
|
| Slice tray |
- Up to 1.6 mm board for this box.
- Too wide for this length: the tip would open past a right angle. Keep the width within twice the length.
- Too narrow for this length: the tip would be too sharp to fold. Keep the width at least half the length.
- At least 30 mm high: lower walls leave no room for the locks.
- Too high for this slice: the lock tabs would cover each other's slots. Lower the height or make the slice longer.
|
| Pizza box |
- Up to 3 mm board for this box.
- Too tall for this size: keep the height within a quarter of the length and of the width.
- Too tall for this size: keep the height within a quarter of the length and of the width.
- Too low for this board: the corner locks need room. Keep the height at least 10 mm + 4 × the board.
|
| Octagon box |
- Up to 1.6 mm board for this box.
|
| Roof box with handle |
- Up to 3 mm board for this box.
- Thickness must be under a fifth of the height.
- Too wide for the handle: keep the width no more than the length.
|
| One bottle wine carrier |
- Up to 1.6 mm board for this box.
- Width must not exceed length.
|
| Two bottle wine carrier |
- Up to 1.6 mm board for this box.
- Width must not exceed length.
|
| Three bottle wine carrier |
- Up to 1.6 mm board for this box.
- Width must not exceed length.
|
| Beer box |
- Up to 1.5 mm board for this box.
- Width must not exceed length.
- Too wide for this length: the end flaps would not reach the dividers. Keep the width within half the length + 70 mm.
|
| Box with lid |
- Lid height can be at most the box height.
- Thickness must be under a fifth of the height.
- Thickness must be under a fifth of the lid height.
|
| Open tray |
- Width must not exceed length.
- Thickness must be under a fifth of the height.
- Too tall for glued corners: keep the height under half the length.
- Too tall for glued corners: keep the height under half the width.
- Too tall for folded corners: keep the height under half the length.
|
| Drawer box |
- Thickness must be under a fifth of the height.
|
| Cake box |
- Thickness must be under a fifth of the height.
|
| Display box |
- The front lip can't be taller than the sides.
- Thickness must be under a fifth of the front lip.
|
| French fries box |
- Up to 1 mm board for this box.
- The height can be at most 1.5 × the length.
|
| Popcorn box |
- Make the height at least half the length.
- Make the height at least half the width.
- Make the width at least half the length.
- Up to 2 mm board for this box.
|